CableDataSheet, Cable and Wire Technical Consulting Service

UL 2556: Jacket and Insulation Shrinkage Evaluation

Overview:
UL 2556 is a testing standard developed by Underwriters Laboratories (UL) to evaluate the performance and durability of electrical cables, including insulation and jacket shrinkage. This standard ensures that cable materials maintain their integrity under thermal stress and remain compliant with safety regulations.

Cable insulation and jacket shrinkage are critical factors affecting the long-term reliability of wires and cables. Excessive shrinkage can expose conductors, leading to electrical failures, safety risks, and performance degradation.

---

Purpose of UL 2556 Shrinkage Test
The primary objective of the UL 2556 shrinkage test is to:

• Assess the thermal stability of cable insulation and jacket materials.
• Ensure that shrinkage remains within allowable limits for safe installation and operation.
• Evaluate material consistency and manufacturing quality.
• Prevent insulation retraction that could cause exposure of live conductors.

UL 2556 is widely used in industries such as power distribution, telecommunications, and industrial automation, where cable reliability is crucial.

---

Test Method for Insulation and Jacket Shrinkage (UL 2556)

UL 2556 specifies a thermal aging and measurement process to evaluate insulation and jacket shrinkage under controlled conditions.

1. Equipment Required:

• Precision calipers or micrometer (accuracy: ±0.01 mm)
• Forced air or convection oven (temperature range: 100°C – 150°C)
• Sample holder to prevent mechanical deformation during testing
• Reference measuring scale (in mm)

2. Test Sample Preparation:

• Cut cable samples to a standardized length (typically 300 mm ± 5 mm).
• Remove any unnecessary outer layers to expose the insulation or jacket under test.
• Mark reference measurement points on the cable before testing.
• Condition the samples at room temperature (23°C ± 2°C) for a minimum of 24 hours before testing.

3. Heating Process:

• Place the samples inside a preheated oven.
• Set the oven to a standardized test temperature: 121°C, 136°C, or 150°C, depending on the material type and application.
• Expose the samples to heat for a specified duration (typically 1 hour ± 5 minutes).

4. Cooling Process:

• Remove the samples from the oven carefully to avoid mechanical stretching.
• Allow them to cool naturally to room temperature (23°C ± 2°C).
• Cooling should occur in a stable environment with no forced air or cooling methods applied.

5. Measurement Process:

• Using a precision caliper, measure the distance from the original reference points to the edge of the insulation or jacket.
• Record shrinkage (reduction in insulation/jacket length) in millimeters.
• Perform multiple measurements to ensure accuracy and take an average for final reporting.

6. Pass/Fail Criteria:

• Shrinkage should not exceed the allowable limits defined in UL 2556.
• Typical limits: ≤ 4 mm for insulation, ≤ 6 mm for jackets (varies based on cable type and industry requirements).
• Excessive shrinkback may result in cable rejection or require redesigning the extrusion and cooling process.

---

Step-by-Step Execution of the UL 2556 Test

Step 1: Prepare the Sample

• Select cable samples that meet the required test conditions.
• Cut them into 300 mm ± 5 mm lengths.
• Use a precision caliper to measure and mark reference points at both ends of the insulation or jacket.
• Ensure that the sample is free of external mechanical stress.

Step 2: Preheat the Oven

• Set the oven to the designated test temperature (121°C, 136°C, or 150°C).
• Ensure the temperature is stable before placing the samples inside.

Step 3: Heat the Sample

• Place the sample on a flat surface inside the oven without bending or stretching.
• Allow the sample to remain in the oven for the required duration (typically 1 hour ± 5 minutes).
• Monitor the sample position to ensure it does not shift during heating.

Step 4: Remove and Cool the Sample

• Carefully take the sample out of the oven using insulated gloves.
• Place it on a non-conductive surface and allow it to cool to room temperature naturally.
• Do not apply any external cooling methods such as fans or water.

Step 5: Measure Shrinkage

• Using a precision caliper, measure the insulation or jacket from the original reference points.
• Compare the new measurements to the initial reference points.
• Calculate the amount of shrinkage in millimeters.

Step 6: Evaluate Pass/Fail Criteria

• Compare the shrinkage values against the maximum allowable limits per UL 2556.
• Record the results and determine whether the cable meets the requirements.
• If the shrinkback exceeds the specified limits, the sample fails the test.

---

Factors Affecting Shrinkage Test Results

Several variables influence the shrinkage behavior of insulation and jackets:

• Material Type: Thermoplastics like PVC and PE tend to shrink more than cross-linked materials like XLPE.
• Manufacturing Process: Poor extrusion and improper cooling can introduce residual stresses that increase shrinkage over time.
• Test Temperature: Higher temperatures accelerate shrinkback, especially in materials with low thermal stability.
• Cable Design: Thicker insulation and jackets generally exhibit lower shrinkage due to material rigidity.

---

Significance of UL 2556 for Cable Manufacturers

UL 2556 ensures that cables meet strict safety and performance requirements. Compliance with this standard helps manufacturers:

• Identify potential defects in insulation and jackets before mass production.
• Optimize material selection and processing conditions.
• Enhance cable longevity and reliability in demanding environments.
• Meet regulatory requirements for electrical safety.

By following UL 2556 test methods, engineers and manufacturers can reduce the risk of premature cable failure, ensuring safe and efficient electrical installations.